<pre id="jjf91"><del id="jjf91"><thead id="jjf91"></thead></del></pre>
        <pre id="jjf91"><b id="jjf91"></b></pre>
        <noframes id="jjf91"><pre id="jjf91"></pre>

                <pre id="jjf91"></pre>

                <pre id="jjf91"><del id="jjf91"><mark id="jjf91"></mark></del></pre>
                  • KB036 使用橙色反光板时需要考虑哪些因素

                    Beginning from about 70 to 100m measuring distance and depending on the quality of a natural surface, the reflectivity decreases to such an extent that reliable distance measurement is no longer possible.

                    However, if a calibrated, orange Dimetix reflective target plate is used, measuring distances of up to 500m are possible (depending on sensor type). More over, a reflective target plate generally causes a higher measuring speed.

                    In addition, the following should be considered:

                    • Selection of a D-series sensor type with suitable measuring range by the means of line “Measuring range on reflective tape” in the specification table. Not only the maximum but also the minimum measuring distance has to be considered
                    • The reflection target plate must not be scratched during assembly, operation and maintenance
                    • Depending on the application conditions, it may be necessary to periodically clean the reflective target plate. Use a soft, non-scratchy cleaning cloth and soapy water for this. Solvents must not be used
                    • The permitted operation temperature range is -20 to +90 °C
                    • For the assembly of the reflection target plate see here
                    • For covering a larger area with the orange Dimetix reflective foil see here

                    KB037 如何粘贴橙色的反射膜

                    Experience shows that for untrained staff gluing on the orange Dimetix reflective foil is difficult and the result is often not satisfying. We therefore strongly recommend that you assign this task to a specialist (e.g. a graphic artist) who is skilled in handling self-adhesive foil.

                    Please also note the following information:

                    • We recommend sticking the foil on an aluminum plate, because we have had good experiences with this material. But other solid and smooth surfaces are also possible.
                    • The surface to which the foil is to be glued must be absolutely free of dust and grease.
                    • We recommend working the foil at 20 °C to 30 °C. The foil must not be worked below 10 °C and above 40 °C.
                    • The surface can be moistened with a little soapy water (approx. 5-8 drops of soap in 500 ml of water). A spray bottle is handy for this. Like this the foil can still be moved on the underlay for a little if necessary,
                    • Then use a soft plastic spatula to wipe out the air bubbles working from the center to the edge. At the same time the soapy water between the foil and the underlay is also wiped out. During this step, special care must be taken to ensure that the foil is not scratched.
                    • Let it dry for a day or two.

                    In many cases, the ready to use, orange Dimetix reflective target plate (Part.No. 500113) can be used as a simple and time-saving option.

                  • KB025 有哪些类型的测量模式供选择

                    KB025 有哪些类型的测量模式供选择

                    The Dimetix sensors support different types of measurements. Depending on the application, it is possible to choose between the following measurement types:

                    • Single distance measurement
                    • Single sensor tracking
                    • Tracking with buffering

                    Single distance measurements: (see top picture)
                    With the command sNg (N represent the ID of the sensor, e.g. ID 0 => s0g) a single distance measurement is triggered. The measurement result is send immediately to all output interfaces.
                    This process can be repeated as soon as the sensor response is received. The single distance measurement type is is often used in monitoring applications.

                    Single sensor tracking: (see center picture)
                    A continuous measurement can be triggered with the command sNh. Depending on the application, it makes sense for the sensor to measure at regular intervals.
                    The desired sampling time can be given with the command sNh+x (x in ms, max. 24h => 85’400’000 ms). This type of measurement is used in various areas (wood industry, steel industry, monitoring, logistics etc.).

                    Tracking with buffering: (see bottom picture)
                    If several sensors are connected to a serial interface (e.g. RS-485), the data line should not be permanently occupied. With the measurement type tracking with buffering sNf (sNf+x, x in ms), the sensor can measure independently of other sensors. The measurement result is buffered in the sensor and only with the command sNq from the PLC, the sensor returns the result. This means that the data line is only used for a short time. This type of measurement is mainly used in the monitoring area with several sensors.

                    Further details in the Technical Reference Manual (see Downloads).

                  • KB028 如何更新传感器的固软

                    KB028 如何更新传感器的固软

                    The Dimetix laser distance sensor can be updated via the USB or the RS-232 interface. The update instructions can be downloaded from the link: Firmware Update.

                    The necessary firmware download files must be requested via Dimetix. This ensures that no effort is made due to unnecessary updating.

                    KB030 如何清洁传感器

                    The laser distance sensors are almost maintenance-free. However, the following checklist for maintenance should be processed cyclically and reacted accordingly:

                    1. Check sensor optics for contamination → Clean laser exit glas and receiver lens carefully if necessary (only use tools suitable for cleaning optical parts / instruments)
                    2. Check valve diaphragm → Valve diaphragm must be free (no water, dirt, etc. on the valve diaphragm)
                    3. Check general sensor status → Sensor must not be damaged, must be correctly assembled and should always be clean

                    Note: Highly contaminated sensor optics can adversely affect the measurement performance (accuracy, speed) or lead to measurement errors.

                  • KB032 怎样使用激光传感器的应用程序,加载和保存配置文件

                    With the Laser Sensor Utility Software from Dimetix, configurations from different devices can be loaded, saved and transferred. It is important that the latest software version is used. The software can be downloaded free of charge from the Dimetix website.

                    If a configuration of an older/other sensor has to be transferred to a new sensor, the following steps must be carried out.

                    1. Connect the old/other sensor to the Laser Sensor Utility
                    2. The current configuration of the sensor can be read out with the menu File -> Read configuration from device (see top image)
                    3. Save the current configuration on your computer: Menu File -> Save configuration as … (see middle image)
                    4. Now the new sensor can be connected to the Laser Sensor Utility
                    5. The configuration can be downloaded directly on the sensor: Menu File -> Download configuration to device (see bottom image)
                    6. The new sensor is now ready for use. Remark: It is possible that some measurement commands have changed slightly compared to older Series (more information can be found in the manuals).
                  • KB050 安装调整

                    The video shows how to use the simple adjustment aid integrated in the D-Series Sensors.
                    See the video also on YouTube: Dimetix Sensor adjustment

                    KB051 如何正确安装可更换的后盖

                    The video shows how to correctly mount the exchangeable cover of the D-Series Sensors.

                    KB052 如何重置

                    The video shows how to perform a reset of the D-Series Sensor.
                    See the video also on YouTube: Dimetix Sensor reset

                    KB053 如何连接工业以太网的通讯接口

                    The video shows the connection of the industrial ethernet sensor extension of the D-Series Sensor.
                    See the video also on YouTube: Dimetix Sensor industrial ethernet connection

                    KB054 如何设置激光传感器

                    The video shows how to connect and configure the D-Series Sensors.
                    See the video also on YouTube: Dimetix Sensor configuration
                  • KB002 测量频率受哪些因素的影响?

                    The measuring rate of the sensors is influenced by different factors. Essentially the signal level of the reflected laser light has an important influence on the measuring rate. On a bright measuring surface (e.g. white) with good reflectivity, a measurement takes less time than on a dark surface (eg. black) with low reflectivity.

                    The following factors can influence the measuring rate / measuring speed in a positive manner:

                    • Condition of the measuring surface (e.g. mat, smooth)
                    • No / little background light (e.g. sunlight, spotlight)
                    • Reduction of the measuring distances
                    • Configuration of the sensor

                    KB005 是否可以测量移动目标?

                    The Dimetix sensors are able to measure on moving targets. Thereby the maximal possible object speed depends on the following factors:

                    • Measuring condition (light conditions, ambient light)
                    • Object- / Measuring surface condition
                    • Sensor specification measuring speed / rate (see Products)

                    Generally with higher measuring rates the maximal object speed will be higher as well. Realize that the measured distance is averaged over the measuring time of one measurement.

                    KB006 什么是测量精度?

                    The measuring accuracy of the Dimetix sensors is specified with a statistical confidential level of 95.4% (corresponds to ISO 1938-2015). This is equivalent to ±2σ or 2 times the standard deviation σ (see the figure).

                    The following distance errors are considered in this measuring accuracy as well:

                    • Distance error due to temperature influence (Sensor temperature)
                    • Linearity error

                    Realize that the sensors do not compensate the humidity, the air pressure or the air temperature. If the environment conditions differ from 60% relative humidity, 953mbar air pressure or 20°C air temperature, the accuracy can be influenced if the measuring distances is longer than 150m. The influence of these environment conditions is described in H. Kahmen & W. Faig: “Surveying”, (1988).

                    KB008 什么是重复精度?

                    KB008 什么是重复精度?

                    The repeatability is achieved by repeatedly approaching the same distance under the same measurement conditions during a short time interval.
                    For example, stable measurement conditions include:

                    • Same distance
                    • Identical measurement target
                    • Same temperature conditions

                    KB009 典型精度和重复精度的区别?

                    The measuring accuracy is specified with ±2σ (see Measuring accuracy). This accuracy includes also distance errors due to temperature changes or linearity errors.
                    In contrast to this, the repeatability is only valid for stable measuring conditions like same distance, identical measuring target, etc. (see Repeatability).

                    KB021 如何达到最佳的测量效果?

                    The best measurement results can be achieved if the following topics are considered:

                    • Select suitable sensor according the application requirenment: Accuracy, measuring distance, measuring speed, temperature range
                    • Optimal measuring surface: Flat, fine, light, matt (for more details see Optimal measureing surface)
                    • Good measuring conditions: Reduce ambient light (e.g. shieldings, shadow, darkness, etc.), stable temperatures, clear and clean air (no dust, fog, rain, etc.)
                    • Select appropriate sensor configuration: Suitable measuring characteristic, longer measurement times, filter options (e.g. Moving average, error suppression), etc.

                    Additional information can be found in the Technical Reference Manual of the laser distance sensors or in other selected FAQ topics.

                    KB024 是否可以在发热发红光的表面上进行测量?

                    KB024 是否可以在发热发红光的表面上进行测量?

                    Basically a measurement on hot or glowing surfaces is possible. This has already been implemented in numerous projects using the Dimetix sensors (see Application Example Steel). Depending on the application, additional measures may be required.

                    It is important to protect the sensor against over temperature. The sensor should therefore be installed at an adequate distance and / or inside a cooled housing.

                    Hot surfaces emit light over the entire spectral range, and thus also within the red wavelength of the laser (type. 650nm). The higher the temperature is, the higher is also this disturbance. (See picture on the left)

                    The filter glass integrated in the laser sensors already reduces disturbances outside of the lasers wavelength. In order to even further reduce disturbances, an additional bandpass filter glass can be installed in front of the sensor optics.

                    For the alignment and selection of the filter glass, follow the instructions Measuring through glass and Minimizing optical disturbances.

                  • KB007 怎样把传感器连接到PLC控制器?

                    The sensors offer different connection possibilities with the PLC systems available on the market.

                    Some of these possibilities are listed below:

                    • RS-422 interface: Sensor commands (ASCII-based) are exchanged between PLC and sensor via RS-422 interface (see AN2010, example with RS-422 interface and Siemens S7).
                    • External PROFIBUS interface: DIMS protocol converter (Dimetix Art.No. 500214) for sensor connection to an existing PROFIBUS interface (see AN2005, example with DIMS PROFIBUS and Siemens S7).
                    • Industrial Ethernet interfaces: Newer sensor types have optionally integrated PROFINET, EtherNet/IP or EtherCAT interfaces (see Dimetix website for details).

                    Other standard integrated sensor interfaces can of course also be used for a connection to a PLC system. More information about the available interfaces of the Dimetix Sensors can be found on the Dimetix website.

                    KB012 RS-232的数据线长度?

                    The RS-232 interface is not designed for long data cables (no differential signals). The cable length depends mainly on the data rates of the RS-232 interface.

                    See the following guidelines:

                    • 19’200 Baud → up to 15m
                    • 115’200 Baud → up to 2m

                    The cable length is also influenced positively / negatively by other factors:

                    • Quality of the cable (Shielding, cross-section, wire resistance, etc.)
                    • Environmental conditions (Disturbance sources like motors, etc.)

                    KB013 RS-422 / RS-485及SSI的信号电缆长度?

                    RS-422 / RS-485 and SSI are differential serial data interfaces designed for long data cables. The cable length depends on the cable quality and data rates.
                    See the following guidelines for the RS-422 / RS-485 interfaces:

                    • 19’200 Baud → up to 1000m
                    • 115’200 Baud → up to 500m

                    See the following guidelines for SSI interfaces:

                    • ≤ 100kBit/s → up to 1000m
                    • ≤ 500kBit/s → up to 200m
                    • ≤ 1000kBit/s → up to 100m

                    Cable type and termination:

                    • Use shielded twisted pair cables only
                    • Termination according to characteristic impedance of the cable (typ. 100 … 150 Ω)

                    The cable length is also influenced positively / negatively by other factors:

                    • Quality of the cable (Shielding, cross-section, wire resistance, etc.)
                    • Environmental conditions (Disturbance sources like motors, etc.)

                    Further details in the Technical Reference Manual (see Downloads).

                    KB014 连接电缆时应注意什么?

                    When selecting the sensor connection cable, the following points should be considered:

                    1. Cable cross-section according to max. sensor current
                    2. Consider wire resistance for long cables (Attention voltage drop through cable)
                    3. Consider cable requirements according to specifications e.g. Shielded twisted pair cable for RS-422 / RS-422 or SSI interfaces. Specifications according to Technical Reference Manual (see Downloads).

                    KB015 对于RS-422 / RS-485及SSI接口,何时建议使用端接?

                    A proper termination of the data lines is recommended in any case. However, for very short data lines and data rates up to approx. 200 kBit/s, a termination is not absolutely necessary.
                    The specifications of the Technical Reference Manual must be observed (see Downloads).

                    KB019 在哪里可找到关于工业以太网接口的常见问题解答?

                    The FAQs for the Industrial Ethernet interfaces are listed in the corresponding Technical Reference Manual (see Downloads).

                    KB027 如何在一根电缆线上连接多个传感器?

                    KB027 如何在一根电缆线上连接多个传感器?

                    Up to 100 sensors can be connected to one line via the RS-422 or RS-485 interfaces. In this case, a different ID must be configured for each sensors, so that all sensor can be addressed by the controller.
                    It is mandatory to use a twisted pair cable which is terminated with a termination resistance of 100-150 ohms.
                    In certain applications, it is necessary that the sensors measure permanently (tracking mode). So that the line is not blocked, the Tracking with Buffering (sNf) in the sensor must be activated for this purpose. The controller can then read the result from each sensor with the command sNq (N is replaced by the ID of the sensor).

                    Further details in the Technical Reference Manual under RS-422/485 interface (see Downloads).

                  • KB001 激光对眼睛安全吗?

                    The Dimetix sensors belong to laser class 2. Sensors of this laser class have visible laser light and a laser power less than 1mW (<1mW).

                    Realize that in normal case the bright light of a class II laser beam into your eyes will cause a normal reaction to look away or close the eyes. This response is expected to protect you from Class II Laser damage to the eyes.

                    If class II laser beams are directly viewed for a long period of time damage to the eyes could result. Avoid looking into a class II laser beam or pointing into another person’s eyes. Avoid viewing class II laser beams with telescopic devices.

                    KB003 哪些为可测量目标?

                    All opaque targets can be measured if they do not have highly reflective surfaces. Reliable measurements on transparent targets are not possible.

                    KB004 灰尘会影响测量过程吗?

                    The influence of dust on distance measurements depends on the density of dust. If the main part of the laser beam is reflected by dust particle, the distance measurement will be influenced in a negative way (measurement errors). However, such conditions can only be found in extreme dusty environments like cement silos.

                    KB010 哪些光干扰源会影响传感器

                    The sensors operate in the wavelength range of 620 … 690nm (corresponds to red light in the visible electromagnetic spectrum). This means that all optical light sources in the same color range can act as potential sources of disturbance.

                    Possible disturbance sources that have to be eliminated / minimized:

                    • Other optical sensors in the same wavelength range
                    • Rotary lights / flashing lights / flashlights
                    • Sunlight

                    Possible approaches to minimizing such disturbance sources:

                    • Separate sensor from other sensors in the same spectrum
                    • Shield sensors with housing / covers

                    KB011 可以透过玻璃测量吗?

                    KB011 可以透过玻璃测量吗?

                    It is not recommended to measure through glass, since there is a signal lost and reflections on the glass may have a negative impact on the accuracy.

                    However, if a glass is the only option for a specific application, check the following points:

                    • Use coated glass to reduce the reflections and signal losses
                    • Install the glass with an angle to the front of the sensor of 5° min.
                    • Keep the glass clean all the time

                    KB016 最佳测量表面是什么?

                    An optimal measurement surface has the following properties:

                    • Flat, fine and not porous
                    • Diffuse reflective (not glossy / reflective)
                    • Bright and stable / low vibration
                    • Bigger than the laser spot

                    The topic can be divided into two use cases:

                    1. Natural measurement surfaces: None / Low Influence on Measurement Surface.
                    2. Selectable measuring surface:
                      • Short ranges → White-matt surface (E.g. white matt sprayed board as an economical solution), or Dimetix orange reflective target for more performance (see Accessory)
                      • Wide ranges → Dimetix orange reflective target (see Accessory)

                    The possible measuring range of the sensors must be checked according to the specifications (see Products).

                    KB017 测量有光泽的表面该注意什么?

                    Measuring on high glossy measuring surfaces should be avoided. Strong signal fluctuations and unwanted reflections can negatively influence the measurement accuracy, cause measuring errors or possibly damage the sensor.

                    If high glossy measurement surfaces are unavoidable, the following recommendations should be considered:

                    • Do not measure perpendicular to the glossy measuring surface
                    • Use optical filter / attenuation (before sensor optics) for signal attenuation

                    KB018 如何使干扰光源最小化?

                    The Dimetix sensors have an integrated filter glass to keep the influence of possible optical sources of interference small. This so-called band-pass filter has the task to let pass only the signal in the wavelength range of the laser (typically 650nm).

                    Nevertheless, especially for applications with very strong optical interference sources, an additional filter or shielding can significantly improve the measurement performance.

                    The following measures can help:

                    • Mount an additional bandpass filter in front of the sensor optics.
                      Note: Do not mount the filter perpendicular to the laser beam, see Measuring through glass.
                      Filter properties: Bandpass filter with CWL: 650nm and FWHM: ~30…40nm (±15…20nm)
                    • Use shielding to protect the sensor optics from optical interference sources. Example: Screening plate, pipe in front of the sensor optics.
                      Attention: The laser output as well as the receiving lens of the sensor must be free and must not be covered.

                    KB020 如何安装橙色发射板?

                    KB020 如何安装橙色发射板?

                    When assembling the orange reflective target plate or reflective foil, the following points must be observed for trouble-free operation:

                    • Only use the Dimetix reflective target plate (see accessories)
                    • Mount the reflective target plate at an angle of 1-2 ° (see figure)
                    • Do not scratch the reflective target plate
                    • Scatter light must not be reflected in sensor optics
                    • The entire laser spot must fit on the reflective target plate (spot size depending on the measuring distance)
                    • For targets with a large horizontal / vertical offset or alignment tolerance (e.g. crane systems), use sufficiently large reflective foil.

                    KB022 激光光斑的大小是多少?

                    KB022 激光光斑的大小是多少?

                    The laser is located with 650 nm in the region of the red spectrum. The laser spot typically becomes larger as a function of the increase in the measuring distance. The laser spot has the shape of an ellipse.

                    Further details in the Technical Reference Manual under specifications (see Downloads).

                    KB023 如何定义反射系数?

                    KB023 如何定义反射系数?

                    The reflectance factor is defined by the ratio of the remitted luminiance of a surface in the direction of measurement to the luminosity of a surface in reference white. As reference white an ideal white and matt surfacse is used.

                    The figure shows some reference values with different measurement characteristics versus distance. From these values, the appropriate target for the desired measurement distance can then be determined.

                    KB033 如何对准激光点?

                    Process laser point alignment (Especially for positioning applications):

                    1. Alignment at close range (about 5cm): Align the sensor to the center of the measurement target (horizontal and vertical). Attention: Adjust the position of the sensor / measuring target only in this step. In the following steps only fine adjustment of the sensor.
                    2. Alignment first distance (about 10m): Readjust the laser point to the center of the measurement target. Use the alignment screws of the sensor or the alignment possibilities of the sensor mounting.
                    3. Alignment further larger distances (about 20 / 50 / 100m): Readjust the laser point to the center of the measurement target. Use the alignment screws of the sensor or the alignment possibilities of the sensor mounting.
                      Note: Typically, alignment is relatively good from about 50m.
                    4. Check alignment: Check if the laser spot is on the measurement target for the entire measurement range. If not, restart with step 2.

                    Note: Film sequence for alignment with Dimetix Sensor, see Dimetix Youtube Channel.

                  Copyright ? 2019 NADO | All right reserved. 鲁ICP备16037561号

                    <pre id="jjf91"><del id="jjf91"><thead id="jjf91"></thead></del></pre>
                        <pre id="jjf91"><b id="jjf91"></b></pre>
                        <noframes id="jjf91"><pre id="jjf91"></pre>

                                <pre id="jjf91"></pre>

                                <pre id="jjf91"><del id="jjf91"><mark id="jjf91"></mark></del></pre>
                                  邻居少妇太爽了A片无码|npp695 国产一级黄片|r9r151 18禁免费无码无遮挡不卡网站|npn361 全免费A级毛片免费看不卡|9pp453 少妇无码一区二区三区免费|nr9809 国产高潮流白浆喷水免费A片激情|pnp682 亚洲精品国产|p0p797 一级A婬看片5O分钟|pnn396 国产激情福利一区二区视频|0rr990 无码人妻aⅴ一区二区三区|rr8947 亚洲国产精品久久久久爰色欲|nr8516 无码专区AAAAAA免费视频|nrn86 黄色网址在线观看|n8n780 精品亚洲Aⅴ无码一区二区|rpp813 黑人粗大无码AV人妻一区|8pr268 午夜无码一区二区三区在线app|nr9884 精品无码国产污污污免费网站|ppp495 亚洲无码视频在线观看|nr9776 在线视频精品|nrn412 无码国产精品一区二区免费视频|n9n425 精品无码国产一区二区久久|rnr133 欧美A片在线观看|7np109 亚洲国产AⅤ精品一区二区综合|nr7156 国产按摩全黄A一级毛片视频|rp7646 色视频在线观看|nnp868 夜夜夜无码一区二区三区|n8r394 国产一区二区三区A片在线播放|pnp76 免费看少妇高潮A片特黄|8pr846 久久久久A级毛片免费看|rr8627 欧美人妻精品一区二区三区|ppp221 亚洲一级av无码毛片久久|r8r192 国产无码视频|rrn329 精品国产污污免费网站入口|6pp767 黄色一区二区|rr6280 亚洲精品A片久久久久久久|rrr719 国产农村妇女一级A一片|r7r188 中文在线天堂中文|nnr495 欧美精品视频|rrr41 国产精品一级毛片不收费|7rn345 一本一本久久aa综合精品|np7997 色欲av自慰一区二区三区|prn861 久久久久久精品一级毛片免费|p7p126 国产一级A片午夜无码免费按摩|rnn994 小13箩利洗澡无码视频网站|7np673 无码视频一区二区三区在线观看|prn313 97人人模人人爽人人少妇|6nn464 国产黃色A片一区二三区|rr6615 久久久久久夜精品精品免费|rpr569